Bona Traffic HD Anti Slip Matt Varnish 4.5 Litre
Bona Traffic HD Anti Slip Matt Varnish 4.5 Litre
Product Advantages
Bona Traffic HD Anti-slip has all the features of Bona Traffic HD but with the additional benefit of being formulated to meet the highest standards for slip resistance in commercial areas, staircases or other situations with an increased risk of spillage and slipping
Extreme durability and scratch resistance
EC1RPlus classified for very low emissions (the industry’s most stringent standard on indoor emissions).
Very low odour and Low solvent content (VOC), <5%.
GreenGuard Gold certified for very low indoor emissions. Recommended for bars, restaurants, schools and nurseries.
DIBt approved for low indoor emissions
Suitable for overcoating compatible pre-finished floors
Clear, non-yellowing formula.
Technical Spec
Coverage rate: 8-10 m² /litre (100-120g/m² ) per coat
Drying time, until: - Ready for sanding/recoating: 2-3 hours* - Full use: 24 hours*
*under normal climate conditions, 20°C/60% R.H.
Preparation
Prior to application the surface must be pre-treated with a waterborne primer from Bona. Ensure floor is acclimatized to its end-use environment, well sanded, dry and free from sanding dust, oil, wax and other contamination. Allow varnish to reach room temperature, insert filter and shake the container thoroughly before use. Optimal application conditions are between 18-25°C and 30-60% relative air humidity.
High temperatures and low humidity shorten, low temperatures and high humidity lengthen drying time. Minimum temperature for use is 13°C.
Application
1. Shake the Traffic HD can and add one bottle of Traffic HD Hardener; immediately shake the mixture thoroughly for 1 minute and then insert the enclosed filter. If mixing smaller quantities of varnish then pour the required amount of varnish into a separate can. 1 litre of varnish corresponds to one part of hardener. 2 litres to two parts and so on. The mixture of varnish/hardener should be used directly or at least within 4 hours.
2. Apply the varnish using a medium pile Roller. Roll with a smooth flowing motion alternately across and with the grain of the wood avoiding accumulations of product. Always maintain a “wet edge” to avoid overlaps. Allow to dry before applying further layers of varnish. Anticipate slightly longer drying time for each layer that is applied.
3. If necessary make an intermediate sanding using a screen or the Bona Scrad System grit P150 (or finer) and remove dust before applying the final layer of varnish. Note: If the previous layer of varnish has been allowed more than 24 hours drying time then an intermediate sanding is always required.
The floor will take light foot traffic approximately 8 hours after the final application and may be put into full use after 12 hours. Allow the surface to dry for at least 1 week before covering with carpets or other floor coverings, or loading with heavy objects. Also avoid damp mopping the floor during this time.
Cleaning
Cleaning: Wipe tools free from excess varnish before cleaning with water. Dried material can be removed with acetone
Maintenance / Aftercare
Clean the floor with Bona Cleaner or Bona Wood Floor Cleaner and a microfibre pad.(These can be purchased together with a Bona spray mop).
Worn surfaces can be renewed from time to time by appliying a new coat of Bona Traffic HD Anti-slip.
Please Note: The floor should not be maintained with a polish or other floor maintenance products as the slip resistance qualities will be affected.
Storage / Shelf life
Shelf life: 1 year from date of production in unopened original container
The temperature must not fall below +5°C or exceed +25°C during storage
Certifications:
GreenGuard Gold
EMICODE class EC1RPLUS
DIBt, safe building product
AS 4586, class P4
BS 7976, low slip potential
DIN 51 130,
| Specification | ||
|---|---|---|
| Coverage |
0.00m²
|
|
| Brand |
Bona
|
|
| Colour |
N/A
|
|
| Use |
Interior
|
|
| Finish |
Matt
|
Product Advantages
Bona Traffic HD Anti-slip has all the features of Bona Traffic HD but with the additional benefit of being formulated to meet the highest standards for slip resistance in commercial areas, staircases or other situations with an increased risk of spillage and slipping
Extreme durability and scratch resistance
EC1RPlus classified for very low emissions (the industry’s most stringent standard on indoor emissions).
Very low odour and Low solvent content (VOC), <5%.
GreenGuard Gold certified for very low indoor emissions. Recommended for bars, restaurants, schools and nurseries.
DIBt approved for low indoor emissions
Suitable for overcoating compatible pre-finished floors
Clear, non-yellowing formula.
Technical Spec
Coverage rate: 8-10 m² /litre (100-120g/m² ) per coat
Drying time, until: - Ready for sanding/recoating: 2-3 hours* - Full use: 24 hours*
*under normal climate conditions, 20°C/60% R.H.
Preparation
Prior to application the surface must be pre-treated with a waterborne primer from Bona. Ensure floor is acclimatized to its end-use environment, well sanded, dry and free from sanding dust, oil, wax and other contamination. Allow varnish to reach room temperature, insert filter and shake the container thoroughly before use. Optimal application conditions are between 18-25°C and 30-60% relative air humidity.
High temperatures and low humidity shorten, low temperatures and high humidity lengthen drying time. Minimum temperature for use is 13°C.
Application
1. Shake the Traffic HD can and add one bottle of Traffic HD Hardener; immediately shake the mixture thoroughly for 1 minute and then insert the enclosed filter. If mixing smaller quantities of varnish then pour the required amount of varnish into a separate can. 1 litre of varnish corresponds to one part of hardener. 2 litres to two parts and so on. The mixture of varnish/hardener should be used directly or at least within 4 hours.
2. Apply the varnish using a medium pile Roller. Roll with a smooth flowing motion alternately across and with the grain of the wood avoiding accumulations of product. Always maintain a “wet edge” to avoid overlaps. Allow to dry before applying further layers of varnish. Anticipate slightly longer drying time for each layer that is applied.
3. If necessary make an intermediate sanding using a screen or the Bona Scrad System grit P150 (or finer) and remove dust before applying the final layer of varnish. Note: If the previous layer of varnish has been allowed more than 24 hours drying time then an intermediate sanding is always required.
The floor will take light foot traffic approximately 8 hours after the final application and may be put into full use after 12 hours. Allow the surface to dry for at least 1 week before covering with carpets or other floor coverings, or loading with heavy objects. Also avoid damp mopping the floor during this time.
Cleaning
Cleaning: Wipe tools free from excess varnish before cleaning with water. Dried material can be removed with acetone
Maintenance / Aftercare
Clean the floor with Bona Cleaner or Bona Wood Floor Cleaner and a microfibre pad.(These can be purchased together with a Bona spray mop).
Worn surfaces can be renewed from time to time by appliying a new coat of Bona Traffic HD Anti-slip.
Please Note: The floor should not be maintained with a polish or other floor maintenance products as the slip resistance qualities will be affected.
Storage / Shelf life
Shelf life: 1 year from date of production in unopened original container
The temperature must not fall below +5°C or exceed +25°C during storage
Certifications:
GreenGuard Gold
EMICODE class EC1RPLUS
DIBt, safe building product
AS 4586, class P4
BS 7976, low slip potential
DIN 51 130,
| Specification | ||
|---|---|---|
| Coverage |
0.00m²
|
|
| Brand |
Bona
|
|
| Colour |
N/A
|
|
| Use |
Interior
|
|
| Finish |
Matt
|
